Inheco SCILA 4位培養箱、四工位細胞培養箱、孵化器、細胞培養箱
在甲板上最小的空間內實現細胞培養參數的最大可變性
在全天候受控的環境中，以更少的錯誤和更高的準確度運行您的實驗和細胞分析。Inheco SCILA細胞培養箱為您提供最大的精確度、卓越的保護和極大的靈活性，同時在自動化平臺上占用最小的空間。
細胞培養箱被細胞生物學家、微生物學家和分子生物學家及其醫療技術助理用于細胞培養實驗室中的自動化細胞培養和基于細胞的貼壁細胞培養物分析。它們允許實驗室通過控制氣體氣氛、濕度和溫度來創造和維持細胞生長的理想生理條件。它們非常好地提供了對環境每一部分的精確控制，同時保護了珍貴的樣品。
強大且可擴展
Inheco SCILA是同類產品中最強大的孵化器。SCILA 4位培養箱專為液體處理系統中的自動化細胞培養應用而設計。因此，它非常適合受控環境中的中低通量細胞處理。通過將SCILA培養箱堆疊在塔中，您可以使用可變參數處理更多樣本，而不會擁擠您的平臺。
受到控制和保護
有了SCILA，您的實驗室可以在完全符合要求的條件下處理每一份樣品，而不用擔心污染。這要歸功于它的銅腔和水管、無菌水系統和易于清潔的設計。溫度、濕度和氣體環境都可以調節，SCILA提供了出色的環境和溫度精度以及溫度均勻性。選擇購買可選的希拉混合氣體混合器，以控制氣體在您的孵化或添加自己的氣體混合系統，可以提供混合氣體。一起使用兩個或三個氣體混合器能夠再現低氧條件，以模擬人體內的條件。
小巧靈活
SCILA的占地面積僅為291毫米高x 250毫米寬x 410毫米長，有4個微孔板(適用于高度小于20毫米的96孔板)或2個深孔選項(高度可達23毫米)，允許您使用微量滴定器或樣品瓶。或者兩者疊加，為您的實驗室提供最大的靈活性。
易于集成
SCILA可以快速連接和調試與SiLA兼容的軟件以及可用的API。它也是物聯網就緒的。它與大多數液體處理站無縫集成，并配有閱讀器和機械臂。
Technical Specifications SCILA
| General specifications – SCILA CO2?MP-4 | |
|---|---|
| Dimensions (H x W x L) | 287 mm x 410 mm x 250 mm |
| Dimensions (H x W x L) with opened drawer | 287 mm x 644 mm x 250 mm |
| Volume of process chamber | 4.6 l |
| Weight | Approx. 16.3 kg |
| Interface | SiLA, Ethernet (RJ45 connector) |
| IP protection class | IP 21 according to IEC60529-1 |
| EMV device class | Group 1 / class A (industrial requirements) |
| SCILA device DC Input?*1) | 24 Vdc |
| Noise while drawer opens | 65 dB(A) |
| Noise closed (only in heating mode) | 45 dB(A) |
| Horizontal precision of the labware in x and y direction (end position per opened drawer) | ± 0.3 mm |
| Vertical precision of labware in z direction (end position per opened drawer) | 1.5 mm |
| Cell culture plates 6-96 wells | Suitable for all kind of robot grippable plates (according to SLAS) |
| Maximum load on drawer | 200 g |
| Height of plate incl. lid | Up to 20 mm with standard labware carrier → chapter 8.5.2 Up to 23 mm with additional labware carrier → chapter 8.5.2 |
1)?SCILA device shall only be powered by the included power supply
| Environmental conditions – SCILA CO2?MP-4 | |
|---|---|
| Tolerable relative humidity: | |
| Operation | 30-60% *2) |
| Transportation and storage | Transportation and storage 10-80% *2) |
| Temperature: | |
| Operation (at altitude 0 – 2500 m) | +15 °C to +32 °C [+59 °F to +90 °F] |
| Transportation and storage (water needs to be removed before shipment) | –20 °C to +60 °C [-4 °F to +140 °F], non condensing?*2) |
2)?Condensate can prevent the SCILA from operating properly and can damage the SCILA.
| Thermal specifications – SCILA CO2?MP-4 | |
|---|---|
| Temperature range | 5 K above ambient to +45 °C |
| Temperature accuracy in steady state at +37 °C) | ±1.0 K |
| Temperature uniformity in steady state at +37 °C | Max temperature difference between plates: 1.0 K within one plate: 0.3 K |
| Temperature recovery at +37 °C (conditions see table below?*3)) | 3 minutes (air temperature) |
| Max. heat up time from +22 °C ambient to +37 °C?*4) | ~ 19 minutes (air temperature) |
| CO2?specifications – Gas inlet SCILA CO2?MP-4 | |
|---|---|
| Pressure range for SCILA Inlet | 0.9 – 1 bar (gas pressure reduction valve necessary if inlet pressure is higher than 1 bar) |
| Flow rate range for SCILA Inlet | 0 – 4.5 ln/min |
| Gas flow – normal | 0.2 l/min |
| Gas flow – boost | 4 l/min |
| CO2?specifications – incubation chamber SCILA CO2?MP-4 | |
|---|---|
| CO2?gas concentration | ≤ 10% |
| CO2 recovery time at 5% (conditions see table below?*3)) | ≤ 5 minutes |
| Humidity specifications – SCILA CO2?MP-4 | |
|---|---|
| Max. water filling volume in incubation chamber | 175 ml |
| Max. operation time at +37 °C, without opening any drawer and without refill | ~ 140 hours |
| Evaporation of sample rH > 85% at +37 °C?*5) | Typically < 0.04% per hour |
| Evaporation of sample without humidification at +37 °C?*5) | < 4% per hour |
| Humidity recovery time (conditions see table below?*3)) | 25 minutes |
| Relative humidity over complete temperature range | 95% +5%/-10% (not actively controlled) |
3)?table showing the standard drawer opening and closure cycle (basis for recovery time tests):
| Standard drawer opening and closure cycle | |
|---|---|
| 1 | SCILA in steady state (2 h after turning on) |
| 2 | Drawer 4 (top drawer): open; hold for 10 s; close |
| 3 | 10 s dead time |
| 4 | Drawer 3: open; hold for 10 s; close |
| 5 | 10 s dead time |
| 6 | Drawer 2: open; hold for 10 s; close |
| 7 | 10 s dead time |
| 8 | Drawer 1: open; hold for 10 s; close |
| 9 | start measuring recovery time |
4)?Start temperature +22 °C, with water prefilled (22 °C), with CO2, measured in air with 2 temperature sensors in drawer 2
5)?Incubation device loaded with 4* NUNC 167008 96 well plates x 250 μl liquid with lid, closed drawers
5)?Incubation device loaded with 4* NUNC 167008 96 well plates x 250 μl liquid with lid, closed drawers
精確、受保護且易于維護
SCILA不僅僅是一個強大的孵化器。它也很容易使用和維護。
設置
- 快速集成–尺寸小，適合您的甲板，加上SiLA兼容軟件，可快速連接。
- 啟動時間僅為19分鐘。快速設置和調試。
- 精確控制溫度、濕度和氣體環境
所有板在37°c時內部溫度均勻，板位置內的溫差低于0.5 K，飽和濕度為0.3 K，內置安全機制以控制水位。 - 快速氣體濃度恢復在打開/關閉抽屜循環后，由于氣體增壓功能和快速(< 10秒)訪問。
- 最大污染保護在加濕系統中具有銅培養室和銅水管。
- 無菌水得到保證–無菌水的外部供應裝置具有自動補水功能，通過水管上可更換的Luer-Lock連接無菌過濾器。
維護
- 易于清潔。我們的專利抽屜設計將完整的抽屜機械裝置放在培養室外面，使帶有圓形邊緣的內部銅表面易于清潔。SCILA的前部可以拆卸，無需清潔和維護工具。
軟件
- SiLA兼容，API可用，IOT就緒。SCILA可快速連接，并為您實驗室的未來發展做好準備。
